Rig Welder Forums  

Go Back   Rig Welder Forums > Search Forums

Showing results 1 to 14 of 14
Search took 0.00 seconds.
Search: Posts Made By: jeffinohio
Forum: General Welding Questions 01-23-2018, 09:36 AM
Replies: 4
Views: 4,629
Posted By jeffinohio
Re: Anadarko Test

How about someone chime in who has taken this test. What is the actual test? I am interested in knowing is it a 12" test"
- What position like 1G or 6G?
-What rod size and what type of rod do...
Forum: Want to buy 09-06-2017, 08:46 PM
Replies: 1
Views: 4,286
Posted By jeffinohio
Re: SS braided twin hose

http://www.deltaoxygensystems.com/

Give them a call and they will hook you up. I recommend the 3 ft high pressure SS braided hose with compression nuts. use your nipple and bull nose fitting or...
Forum: Machines, tools, etc. 08-28-2017, 08:52 AM
Replies: 3
Views: 3,647
Posted By jeffinohio
Re: Vantage receptacles

Tidweld sells a nice 120volt pig tail that plugs into your 30 amp/220v outlet. You can run your big grinder on it and bare down on the grinder and not worry about blowing the breaker. Or you could...
Forum: Work 06-21-2017, 05:08 AM
Replies: 6
Views: 5,790
Posted By jeffinohio
Re: Welder Opportunity

LMBO. Kyle. that's too funny.
Forum: Machines, tools, etc. 02-10-2017, 06:16 PM
Replies: 14
Views: 9,557
Posted By jeffinohio
Re: Pipe pro 350 wireless remote

What brand of remote do you have? I had a remote that had a goofy toggle looking switch at the machine for 2 different modes. My wireless remote would not increase amps past 110 amps. Once I figured...
Forum: Everything Else 01-18-2017, 05:47 PM
Replies: 2
Views: 7,094
Posted By jeffinohio
New Truck Bed I built

Hello guys. Been working on building a new truck bed during my off time. Finally got it done. Not sure if I attached the picture correctly but you can check out my pictures on youtube and let me know...
Forum: Machines, tools, etc. 09-25-2016, 05:24 PM
Replies: 34
Views: 31,857
Posted By jeffinohio
Re: Lincoln Cross Country 300

Hey smoke stack. The vantage 300 works fine with a Lincoln Magnum Spool gun. I've ran at least 40, one pound spools threw it while building an aluminum rig bed. Other than that itís been over 20...
Forum: Work 03-18-2016, 02:09 AM
Replies: 0
Views: 3,506
Posted By jeffinohio
Single Hand Needed Ohio

Anyone looking for a single hand job? 40 days left of refinery shutdown. Must have steel toe boots, 10 hours MOST Safety Training. Past 2 " 6-G Carbon steel 6010 root, 7018 fill and cap test. Past...
Forum: Everything Else 01-24-2016, 02:18 AM
Replies: 54
Views: 25,114
Posted By jeffinohio
Re: Union questions

Short answer is Yes. Many local bylaws say after you retire you can't work in the trade or your pension is frozen for 6 months. Some weld for a different trade for a short shut down to get a little...
Forum: Work 11-28-2015, 05:47 AM
Replies: 3
Views: 3,877
Posted By jeffinohio
Re: Getting (helper) work in NY

You might get a ton of different responses but one that works is go work for the competition. Find out who the biggest competitors are with the union contractors and go get a job with them. After 6...
Forum: General Welding Questions 10-21-2015, 03:19 AM
Replies: 63
Views: 31,859
Posted By jeffinohio
Re: Using a squirt gun for stainless

8" schedule 10. I would just tig it and be done with it. Cut it with a mataba cut off wheel. That would be fastest in the field for me to set it all up and knock it out.
Forum: Everything Else 07-30-2015, 05:40 PM
Replies: 356
Views: 103,362
Posted By jeffinohio
Re: I hate.....

Who Is Covered Under The Arkansas Lemon Law?
Any consumer who buys or leases, and registers a new motor vehicle in the State of Arkansas is covered by the Lemon Law.
The consumer is protected...
Forum: General Welding Questions 06-14-2015, 06:40 AM
Replies: 59
Views: 34,540
Posted By jeffinohio
Re: up hand 6010 root... giving me some troubles

A little hole that you burn threw and fill up while doing your hot pass should be fine on an x-ray. Look in the pipe if you can. If it is a test I would not recommend continuing your hot pass after...
Forum: Work 06-13-2015, 04:32 PM
Replies: 64
Views: 26,618
Posted By jeffinohio
Re: Union rigwelders

Yes. 798 is not the only downhill welding local. I am new to downhill and am just starting to put my rig together. Local 190 Ann Arbor MI has a Gas distribution side of their local. They cover MI and...
Showing results 1 to 14 of 14

 
Forum Jump

All times are GMT -7. The time now is 06:28 PM.


Powered by vBulletin® Version 3.8.7
Copyright ©2000 - 2021, vBulletin Solutions, Inc.